断桥铝穿条设备|断桥铝滚压机|断桥铝开齿机_济南合飞数控设备有限公司 断桥铝穿条设备|断桥铝滚压机|断桥铝开齿机_济南德恩机械设备有限公司
行业动态

当前位置:首页 > 新闻动态 > 行业动态

断桥铝穿条设备浅谈真空木纹转印机如何操作

发布人:admin  发布时间:2020-10-12  浏览次数:197

1、接通电源后,查看指示灯是否正常,如果指示灯为红色把三项火线其中两项线头调整一下,如果显示绿灯为正常。

1, after the power supply, check the indicator light is normal, if the indicator light is red, three items of FireWire, two thread adjustments, if the green light is normal.

2、开机前设定温度,防盗门 钢质门一般温度为246-256度,钢板门温度为210-220度,转印时间设定钢木门为2-3分钟,防盗门为4-5分钟,钢板门为12-16分钟。

2, before setting up the temperature, anti-theft door steel door general temperature is 246-256 degrees, steel door temperature is 210-220 degrees, transfer time set steel door for 2-3 minutes, anti-theft door for 4-5 minutes, steel door for 12-16 minutes.

3、正常工作先预热机器,必须先抽真空,然后工作台推到加热仓里面进行几分钟的加热(切记一定抽真空预热,否则损坏硅胶模具)。正常工作发现转印工件木纹不清晰,是因为温度低或时间短造成的。把温度适当提高5-10度或时间延长20-30秒。

3, the normal work to preheat the machine, you must first vacuum, and then push the work station to the heating chamber inside for a few minutes heating (remember to vacuum preheating, otherwise damage silicone mold). Normal work has shown that the graining of the workpiece is not clear because of low temperature or short time. Increase the temperature by 5-10 degrees or 20-30 seconds longer.

4、真空压力表调整为低压0.8Mpa,高压1.2Mpa为正常。

4. Vacuum pressure gauge is adjusted to low voltage 0.8Mpa, high voltage 1.2Mpa is normal.

5、转印机每1-2个月换一次真空泵油,经常检查油的液面。

5, transfer machine every 1-2 months for a vacuum pump oil, often check the oil level.

6、新设备使用1-2天后应检查各个接线头是否松动拧紧各接线(拧紧电器箱电器接线,加热管连接线)。

6, the use of new equipment 1-2 days later, should check the wiring head is loose, tighten the wiring (tighten the electrical box, electrical wiring, heating pipe connection line).

7、真空罐设有放水阀,如果设备处在潮湿环境中,真空罐应隔几天排放一下水。

7. The vacuum tank is equipped with a drain valve. If the equipment is in a humid environment, the vacuum tank should be discharged every few days.

8、新设备或新更换的硅胶板,在使用几天后,正常工作中如果出现横竖皱折,应立即停止使用,调整硅胶板松紧度,否则严重损坏硅胶板。

Silica gel plate 8, new equipment or new replacement, in the use of a few days later, the normal work if the horizontal fold, should immediately stop using, adjust the tightness of the silica gel plate, otherwise severely damaged silicon sheet.

9、下班后先关掉急停开关,切断电源。

9, after work, turn off the emergency stop switch first, cut off the power supply.


推荐产品
  • 穿条机
  • 滚压复合机
  • 开齿穿条一体机
  • 双轴数控四组滚压复合机GYJ-SSK2
  • 数控滚压复合机GYJ-SK5
  • 双轴数控滚压复合机(普通型)GYJ-SK2
  • 滚压复合机GYJ-01
  • 开齿机(重型)
  • 开齿机(重型)
  • 全数控滚压复合机
  • 高配开齿机GKCJ-01
  • 数控开齿机
  • 铝型材填充发泡机
  • 双轴数控滚压复合机GYJ-SK2
  • 数控穿条机

网站首页|关于我们|新闻动态|产品展示|历届展会|客户留言|联系我们

版权所有:济南德恩机械设备有限公司  备案号:鲁ICP备16044530号  地址:济南槐荫区美里北路工业开发区  电话:0531-88933293

手机:15265318532 / 13355418532 网址:www.hefeisk.com  技术支持:网搜科技  流量统计: